MOXA ioMirror E3210
Ethernet Peer-to-Peer I/O Server 8 Digital Inputs, 8 Digital Outputs
- Direct input-to-output signal communication over IP
- High speed Peer-to-Peer I/O within 20 ms
- One physical alarm port for connectivity status
- Quick and easy utility and web-based settings
- Local alarm channel
- Remote alarm message
- Supports Modbus/TCP for remote monitoring
- Optional LCD module for simple setting
Direct input-to-output communication over IP
The MOXA ioMirror E3000 Ethernet I/O server is designed as a cable-replacement solution that connects remote digital input signals to output signals over an IP network. The MOXA ioMirror E3210 provides 8 digital input and 8 digital output channels and a 10/100M Ethernet interface. Up to 8 pairs of digital input and output signals can be exchanged over Ethernet with another ioMirror E3210 as well as to a local PLC or DCS controller. Over a local area network, the ioMirror achieves low signal latency, typically 20 ms. With ioMirror servers, remote sensors can now be connected to local controllers or display panels over copper, fiber, or wireless Ethernet infrastructures. Signals can be transmitted over virtually unlimited distances, without noise problems.
Split sensor signals to sixteen different locations
The MOXA ioMirror E3000 can split one input signal to two digital output channels at two different IP addresses. Eight tank level signals could be monitored at sixteen different display panels at the same time.
Local alarm with remote alarm messages to monitor connectivity
The MOXA ioMirror E3210 has a 24 VDC alarm output channel that can activate an attached buzzer or display LED when the connection fails. In addition, both ioMirror modules can send messages to the event log software. This ensures that at least one of the warning messages will reach the event log software.
The MOXA ioMirror E3000 Ethernet I/O server is designed as a cable-replacement solution that connects remote digital input signals to output signals over an IP network. The MOXA ioMirror E3210 provides 8 digital input and 8 digital output channels and a 10/100M Ethernet interface. Up to 8 pairs of digital input and output signals can be exchanged over Ethernet with another ioMirror E3210 as well as to a local PLC or DCS controller. Over a local area network, the ioMirror achieves low signal latency, typically 20 ms. With ioMirror servers, remote sensors can now be connected to local controllers or display panels over copper, fiber, or wireless Ethernet infrastructures. Signals can be transmitted over virtually unlimited distances, without noise problems.
Split sensor signals to sixteen different locations
The MOXA ioMirror E3000 can split one input signal to two digital output channels at two different IP addresses. Eight tank level signals could be monitored at sixteen different display panels at the same time.
Local alarm with remote alarm messages to monitor connectivity
The MOXA ioMirror E3210 has a 24 VDC alarm output channel that can activate an attached buzzer or display LED when the connection fails. In addition, both ioMirror modules can send messages to the event log software. This ensures that at least one of the warning messages will reach the event log software.
Inputs and Outputs
Digital Inputs
8 channels
Digital Outputs
8 channels
Alarm Port Output
1 channel
Digital Input
Sensor Type
Wet Contact (NPN), Dry Contact
I/O Mode
Digital Input
Dry Contact
- On: short to GND
- Off: open
Wet Contact (source type)
- On: 0 to 3 VDC
- Off: 10 to 30 VDC
Common Type
8 points per COM
Isolation
3K VDC or 2K Vrms
Digital Filtering Time Interval
Software selectable
Over-voltage Protection
36 VDC
Digital Output
Type
Sink
I/O Mode
Digital Output
Over-voltage Protection
45 VDC
Over-current Protection
2.6 A (4 channels @ 650 mA)
Over-temperature Shutdown
160°C
Current Rating
200 mA per channel
Isolation
3K VDC or 2K Vrms
Alarm Port Output
Current Rating
200 mA per channel
Isolation
3K VDC or 2K Vrms
LAN
Ethernet
1 x 10/100 Mbps, RJ45
Protection
1.5 KV magnetic isolation
Protocols
Modbus/TCP, TCP/IP, UDP, DHCP, Bootp, HTTP, SNTP
Power Requirements
Power Input
24 VDC nominal, 12 to 48 VDC
DO Power
24 VDC nominal, up to 45 VDC
Power Consumption
136 mA @ 24 VDC
Physical Characteristics
Wiring
I/O cable max. 14 AWG
Dimensions
115 x 79 x 45.6 mm (4.53 x 3.11 x 1.80 in)
Weight
205 g
Environmental Limits
Operating Temperature
-10 to 60°C (14 to 140°F)
Storage Temperature
-40 to 85°C (-40 to 185°F)
Ambient Relative Humidity
5 to 95% (non-condensing)
Altitude
Up to 2000 m and higher altitude on demand
Standards and Certifications
Safety
UL 508
EMI
FCC Part 15 Subpart B Class A, EN 55022 Class A
EMS
IEC 61000-4, IEC 61000-6
Shock
IEC 60068-2-27
Freefall
IEC 60068-2-32
Vibration
IEC 60068-2-6
- Ordering Information
Available Modules | |
ioMirror E3210 | Ethernet Peer-to-Peer I/O with 8 digital inputs and 8 digital outputs |
Customers who viewed this item also viewed