MOXA ioLogik E2242
Smart Ethernet remote I/O with Click&Go, 4 AIs, and 12 DIOs
- Active communication with patented MX-AOPC UA Server and Active OPC server
- Smart alarm management with email, SNMP traps, TCP, UDP
- Save time and wiring costs with peer-to-peer communication
- Front-end intelligence with patented Click&Go control logic, up to 24 rules
- Simplify I/O management with MXIO library for Windows or Linux
- Web browser configurations over HTTP
- Supports SNMP v1/2c/3
- Wide operating temperature range of -40 to 75°C (-40 to 167°F)
Moxa’s ioLogik E2200 is a new type of Ethernet micro RTU controller, which is a PC-based data acquisition and control device that uses proactive, event-based reporting to control I/O devices. Unlike traditional RTUs, which are passive and must poll for data, Moxa’s ioLogik E2200 series with Active OPC Server makes seamless connection with SCADA systems a reality. In addition, SNMP is used for communicating with an NMS (Network Management System) for IT field users. The I/O status of an Ethernet micro RTU controller can be reported and controlled automatically on-site based on user specified conditions. This report-by-exception approach, which is new to PC-based monitoring, requires far less bandwidth than traditional polling methods.
Actice Alarming with Local Intelligence
The ioLogik E2200 Micro RTU supports simple and powerful Click&Go™ technology to deliver event-driven reports and allow alarm messages to be sent by email, TCP/UDP, and SMNP Trap with real-time stamps. With built-in Click&Go™ intelligence, the ioLogik E2200 micro RTU can be used for simple output control when it is triggered by input status, without the need for a PC controller. The ioLogik E2200 micro RTU reports I/O status automatically based on user-specified conditions. This report by-exception approach requires far less bandwidth than the traditional polling approach.
Actice Alarming with Local Intelligence
The ioLogik E2200 Micro RTU supports simple and powerful Click&Go™ technology to deliver event-driven reports and allow alarm messages to be sent by email, TCP/UDP, and SMNP Trap with real-time stamps. With built-in Click&Go™ intelligence, the ioLogik E2200 micro RTU can be used for simple output control when it is triggered by input status, without the need for a PC controller. The ioLogik E2200 micro RTU reports I/O status automatically based on user-specified conditions. This report by-exception approach requires far less bandwidth than the traditional polling approach.
ioLogik E2242 Specifications
- Inputs and Outputs
Analog Inputs
4 channels
Configurable
DI/Os 12 channels
- Analog Input
Type
Differential input
Resolution
16 bits
I/O Mode
Voltage / Current
Input Range
±150 mV, 0 to 150 mV, ±500 mV, 0 to 500 mV, ±5 V, 0 to 5 V, ±10 V, 0 to 10 V, 0 to 20 mA, 4 to 20 mA
Accuracy
±0.1% FSR @ 25°C
±0.3% FSR @ -10 and 60°C
±0.5% FSR @ -40 and 75°C
Sampling Rate
All channels: 32 samples/sec
Per channel: 8 samples/sec
Single channel: 100 samples/sec
Input Impedance
200k ohms (min.)
Built-in Resistor for Current Input
120 ohms
- Digital Input
Sensor Type
Wet Contact (NPN or PNP) and Dry Contact
I/O Mode
DI or event counter
Dry Contact- On: short to GND
- Off: Open
Wet Contact (DI to GND)- On: 0 to 3 VDC
- Off: 10 to 30 VDC
Common Type
6 points per COM
Isolation
3k VDC or 2k Vrms
Counter Frequency
900 Hz
Digital Filtering Time Interval
Software selectable
- On: short to GND
- Digital Output
Type
Sink
I/O Mode
DO or Pulse Output
Pulse Output Frequency
1 kHz
Over-voltage Protection
45 VDC
Over-current Protection
2.6 A (4 channels @ 650 mA)
Over-temperature Shutdown
175°C (min.)
Current Rating
200 mA per channel
Isolation
3k VDC or 2k Vrms
- Power Requirements
Power Consumption
178 mA @ 24 VDC
- MTBF (mean time between failures)
Time
204,391 hrs
Database
Telcordia (Bellcore)
Common Specifications
- LAN
Ethernet
1 10/100 Mbps RJ45 port
Protection
1.5 kV magnetic isolation
Protocols
Modbus/TCP, TCP/IP, UDP, DHCP, BOOTP, SNMP, HTTP, CGI, SNTP, SMTP
- Serial Communication
Interface
RS-485-2w: Data+, Data-, GND (3-contact terminal block)
Serial Line Protection
15 kV ESD for all signals
- Serial Communication Parameters
Parity
None
Data Bits
8
Stop Bits
1
Flow Control
None
Baudrate
1200 to 115200 bps
Protocol
Modbus/RTU
- Power Requirements
Power Input
24 VDC nominal, 12 to 36 VDC
- Physical Characteristics
Wiring
I/O cable max. 14 AWG
Dimensions
115 x 79 x 45.6 mm (4.53 x 3.11 x 1.80 in)
Weight
under 250 g
Mounting
DIN rail or wall
- Environmental Limits
Operating Temperature
Standard Models: -10 to 60°C (14 to 140°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)
Storage Temperature
-40 to 85°C (-40 to 185°F)
Ambient Relative Humidity
5 to 95% (non-condensing)
Altitude
Up to 2000 m
Note Please contact us if you require products guaranteed to function properly at higher altitudes.
- Standards and Certifications
Safety
UL 508
EMI
EN 61000-3-2; EN 61000-3-3; EN 61000-6-4;
FCC
Part 15, Subpart B, Class A
EMS
EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5,
EN 61000-4-6, EN 61000-4-8, EN 61000-4-11, EN 61000-6-2
Shock
IEC 60068-2-27
Freefall
IEC 60068-2-32
Vibration
IEC 60068-2-6
Green Product
RoHS, CRoHS, WEEE
- Ordering Information
Available Modules ioLogik E2242 Ethernet Micro RTU Controller with 4 analog inputs and 12 configurable DIOs,
-10 to 60°C operating temperatureioLogik E2242-T Ethernet Micro RTU Controller with 4 analog inputs and 12 configurable DIOs,
-40 to 75°C operating temperature
Customers who viewed this item also viewed