Advantech AMAX-4850
16-ch IDI & 8-ch PhotoMOS EtherCAT Remote I/O module
- Suitable for EtherCAT networks
- 16-ch digital input and 8-ch PhotoMOS Relay output (Form A)
- 1500 VDC optical isolation for relay outputs
- Quick removable European type connector
- LED indicators for I/O status
- Supports EtherCAT Distributed Clock (DC) mode and SyncManager mode
- Two Rotary switches for up to 256 slave IDs
The AMAX-4850 is an industrial EtherCAT slave module equipped with the EtherCAT protocol. Its compact size and DIN-rail mount kit can install easily in a cabinet. Euro type pluggable terminal blocks and LED indicator help users to maintain and set up their system. All digital input and PhotoMOS Relay Output channels are protected by isolation circuits.
Compact Size
High density channel count in a compact design helps increase space utilization ratio. Din-rail mounting kit ensures easy installation in cabinets.
Easy to Maintain
Terminal block, LED indicator, Switch and EtherCAT port can be operated at front side. These provide a convenient way to wire, test, debug or maintain. In particular, AMAX-4800 series equip euro type pluggable terminal block to insert wires without screw tools. These features can help user to reduce maintenance cost and time.
Good expandability
Since a total of 65,535 nodes per network segment can be connected, the I/O channel amount will not be limited by PCI/PCIE slot any more. The physics of Ethernet allow a cable length of up to 100 m (300 ft) between two nodes, so expensive signal cable will be replaced. This means less IPC, simpler wiring topology and lower cost.
Synchronization
The synchronization time between each slave module is one of important parameter for motion control. AMAX-4800 series support EtherCAT distributed Clock. By using distributed clocks , modules can calibrate the time difference less than 1 us to output synchronize signal.
Compact Size
High density channel count in a compact design helps increase space utilization ratio. Din-rail mounting kit ensures easy installation in cabinets.
Easy to Maintain
Terminal block, LED indicator, Switch and EtherCAT port can be operated at front side. These provide a convenient way to wire, test, debug or maintain. In particular, AMAX-4800 series equip euro type pluggable terminal block to insert wires without screw tools. These features can help user to reduce maintenance cost and time.
Good expandability
Since a total of 65,535 nodes per network segment can be connected, the I/O channel amount will not be limited by PCI/PCIE slot any more. The physics of Ethernet allow a cable length of up to 100 m (300 ft) between two nodes, so expensive signal cable will be replaced. This means less IPC, simpler wiring topology and lower cost.
Synchronization
The synchronization time between each slave module is one of important parameter for motion control. AMAX-4800 series support EtherCAT distributed Clock. By using distributed clocks , modules can calibrate the time difference less than 1 us to output synchronize signal.
Communication
- Interface
EtherCAT
Data transfer medium
Ethernet/EtherCAT cable (min. CAT 5), shielded
Distance between modules
Max. 100 m (100BASE-TX)
Communication Cycle Time
200us
Data transfer rates
100 Mbps
Configuration
Not required
Digital Input
- Channels
16
Input voltage
Logic 0: 3 V max.; Logic 1: 10 V min. (30 V max.)
Isolation protection
2,500 V DC
PhotoMOS Relay Output
- Channels
8
Relay type
PhotoMOS SPST(Form A)
Load Voltage
60V (AC peak or DC)
Load current
1.2A
Peak load current
4A @100ms(1 pulse)
Isolation protection
1,500 V DC
Turn-on time
1 ms typical
Turn-off time
0.6 ms typical
General
- Connectors
10-pin 3.81 mm terminal block * 4 (I/O)
3-pin 3.81 mm screw terminal block (power) RJ-45 * 2 (EtherCAT)
Dimensions
120 mm x 120 mm x 40 mm
Operating temperature
-20 ~ 60°C (32 ~ 140°F)
Storage temperature
-40 ~ 70°C (-40 ~ 158°F)
Storage humidity
5 ~ 95% RH (non-condensing)
Power supply
10 ~ 30 V DC
Power Consumption
Typical 85mA @24V; Max. 110mA @24V
Ordering Information
- AMAX-4850-AE
- 16 IDI & 8 PhotoMOS EtherCAT Remote I/O module
96PS-A40WDIN
- DIN RAIL A/D 100-240V 40W 24V
Customers who viewed this item also viewed